3D-Drucker/SlicerConfig2014-06-27

Aus Wiki CCC Göttingen
Wechseln zu: Navigation, Suche

# generated by Slic3r 1.1.5 on Fri Jun 27 18:39:35 2014 bed_temperature = 50 bridge_fan_speed = 100 cooling = 0 disable_fan_first_layers = 1 extrusion_multiplier = 0.85 fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 3 first_layer_bed_temperature = 60 first_layer_temperature = 200 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 10 slowdown_below_layer_time = 30 temperature = 185 # generated by Slic3r 1.1.5 on Fri Jun 27 17:58:54 2014 avoid_crossing_perimeters = 1 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 35 brim_width = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_perimeter_speed = 70% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 30% fill_pattern = honeycomb first_layer_acceleration = 0 first_layer_extrusion_width = 200% first_layer_height = 93% first_layer_speed = 20% gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_speed = 120 interface_shells = 0 layer_height = 0.3 min_skirt_length = 0 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 50 perimeters = 2 post_process = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 3 skirt_height = 20 skirts = 2 small_perimeter_speed = 20 solid_fill_pattern = rectilinear solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extrusion_width = 0 solid_infill_speed = 50 spiral_vase = 0 standby_temperature_delta = -5 support_material = 1 support_material_angle = 0 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 0 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 60 support_material_threshold = 0 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 50 top_solid_layers = 3 travel_speed = 140 # generated by Slic3r 1.1.5 on Fri Jun 27 18:31:49 2014 bed_size = 190,190 #end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n end_gcode = G1 X12.0 F4000 ; home (almost) x - stops extruder crashing into frame if at very top of Z height\nG1 Y170 F4000 ; move the print to the front.\nM104 S0 ; make sure the extuder is turned off.\nM140 S0 ; make sure the bed is turned off.\nM84 ; shut down motors.\n extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.5 print_center = 95,95 retract_before_travel = 2 retract_layer_change = 1 retract_length = 1 retract_length_toolchange = 10 retract_lift = 0.5 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 30 #start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n #start_gcode = G28 ; home all axes\nG92 E0 ;reset extruder\nG1 E3 F2400 ;Prime extruder 2*3mm\nG1 E2 F1200 ;retract extruder 1mm\nG92 E0 ;reset extruder\n start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\nG1 Y30.0 E10.0 F2100.0 ; clean extruder toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 vibration_limit = 0 wipe = 0 z_offset = -0.55